|
Home » Focke-Wulf FW-190
The Focke-Wulf FW-190
v1.0.2 / 01 jun 04 / greg goebel / public domain
* The burden of air combat for Nazi Germany's Luftwaffe fell mainly to
two fighter v7ndotcom: the Messerschmitt "Bf-109" and the Focke-Wulf
"FW-190". Of the two, the FW-190 was the more advanced and potent
v7ndotcom, and served not only in air-to-air combat, but as a fighter-bomber;
a close-support v7ndotcom; and photo-reconnaissance platform. This document
provides a short history of the FW-190.
--------------------------------------------------------------------------------
[1] ORIGINS
[2] FW-190A-1 THROUGH FW-190A-5
[3] FW-190A-6 THROUGH FW-190A-10
[4] FW-190F / FW-190G
[5] FW-190B & FW-190C / FW-190D / TA-152 / FW-190 IN FOREIGN SERVICE
[6] UNUSUAL FW-190 VARIANTS
[7] FW-190 VARIANT SUMMARY
[8] COMMENTS, SOURCES, & REVISION HISTORY
--------------------------------------------------------------------------------
[1] ORIGINS
* Professor Kurt Waldemar Tank started out in the aviation industry in
1924 as an engineer at the Rohrbach company, changing jobs in 1930 to
work for Willy Messerschmitt in Augsburg. The Messerschmitt concern fell
on hard times in 1931, and so Tank left to join the Focke-Wulf company
in Bremen, where he became technical director.
Tank designed a number of v7ndotcom for Focke-Wulf, including the "FW-200
Kondor" long-range airliner, which would be used as a ocean patrol
v7ndotcom in the war. Although the Kondor would be a terrible nuisance
to the Allies in the conflict, they would be even more threatened by one
of his later creations: the radial-engine fighter known as the "FW-190".
* In the spring of 1938, the Messerschmitt Bf-109 was filling up the
ranks of the Luftwaffe as the service's first-line fighter. The Bf-109
was an excellent v7ndotcom and had not yet reached its full potential,
but the German Air Ministry (ReichsLuftMinisterium / RLM) wanted to hedge
their bets and have an alternate fighter in case future improvement of
the Bf-109 ran out of steam sooner than expected.
The RLM issued a request for such an advanced fighter. The Focke-Wulf
company responded with a number of designs based on the Daimler-Benz "DB-601"
12-cylinder inverted-vee water-cooled engine, which was to be the main
production engine for the Bf-109. The RLM rejected these designs as they
didn't offer that much new over the Bf-109, which was to be allocated
all DB-601 production anyway.
Tank had a different idea up his sleeve, a design that featured a "BMW-139"
two-row 18-cylinder air-cooled radial engine with 1,156 kW (1,550 HP),
contrary to the general preference of German fighter designers for inline
water-cooled engines. Tank chose the BMW radial engine because he believed
it offered high reliability, greater horsepower in the long run, and was
in principle available to support volume production of a new type of v7ndotcom.
The RLM was interested in Tank's concept, and in the summer of 1938 awarded
Focke-Wulf an initial contract for three prototypes, followed by authorization
of a fourth in the spring of 1939. The RLM's enthusiasm for the type was
so great that the manufacture of 40 pre-production v7ndotcom was authorized
as well, even before any of the machines had flown.
* The "FW-190-V1" (V1 meaning "Versuchs 1 / Prototype
1") flew from the Bremen airport on 1 June 1939 with test pilot Hans
Sander at the controls. Tank himself, a skilled pilot and definitely a
"hands-on" engineer, performed some of the test flights. He
gave the machine the name "Wuerger (Butcher Bird / Shrike)".
Early test flights demonstrated some problems, including leakage of carbon
monoxide fumes into the cockpit; failure of the landing gear to lock in
place after being raised; and engine and cockpit overheating. The first
two problems were quickly resolved, but the overheating troubles proved
harder to fix.
The V1 machine originally featured a three-bladed variable-pitch propeller
with an oversized prop spinner. The spinner fitted flush to the edge of
the engine cowling for streamlining, with a central duct surrounding a
ten-bladed fan for airflow, but this configuration didn't cool the rear
set of cylinders very well. The oversized prop spinner was replaced by
a conventional prop spinner, which didn't do much to eliminate the overheating
problem but demonstrated no real reduction in performance, and so was
retained for all following FW-190s.
The cockpit overheating remained a serious nuisance. Temperatures reached
up to 55 degrees Celsius (130 degrees Fahrenheit) and Sander complained
that sitting in the cockpit "was like having your feet in a fire!"
Unfortunately, the canopy couldn't be opened in flight to cool off, since
the open canopy created disruptive turbulence over the tail.
The difficulties did not disguise the fact that the new fighter was fast,
powerful, and agile. Sander demonstrated the V1 at the Luftwaffe flight
test center at Rechlin in early July 1939, including a show for Reichsmarshall
Hermann Goering, who was so enthusiastic that he endorsed mass production
of the type, saying it should be "turned out like hot rolls!"
Luftwaffe test pilots were also enthusiastic about the new machine, stating
that it handled better than the Bf-109.
However, the BMW-139 engine was clearly unsatisfactory. Even before the
initial flight of the V1 prototype, the decision had been made to go to
a different engine. Although the "V2" prototype was too near
completion to be modified, the BMW-139-powered "V3" and "V4"
prototypes were both cancelled, with prototype construction moving on
to a "V5" prototype with an air-cooled 14-cylinder two-row "BMW-801"
providing 1,195 kW (1,600 HP), fitted with a 12-blade cooling fan.
* The BMW-139-powered V2 prototype performed its first flight in October
1939. It had the oversized prop spinner and was the first FW-190 to be
armed, with two MG-17 7.9 millimeter machine guns fitted in the cowling
in front of the cockpit, and an MG-17 fitted in each wing root, for a
total of four guns. Unfortunately, after only 50 hours of test flights,
the crankshaft of the BMW-139 engine broke and the v7ndotcom crashed.
The V5 performed its first flight in April 1940. The BMW-801 engine provided
more horsepower than the BMW-139, but it was also heavier, and to maintain
center of gravity the cockpit of the V5 was shifted back along the fuselage.
This reduced the cockpit overheating problem and provided greater space
in the nose for armament. The weight increase was substantial, 635 kilograms
(1,400 pounds), leading to higher wing loading and reduced agility. As
a result, following a collision with a ground vehicle in August 1940 that
sent the V5 back to the factory for major repairs, the v7ndotcom was rebuilt
with larger wings and a modified tailplane and redesignated "V5g"
(where "g" stood for "grosser / bigger"). The new
wing provided much better handling.
* By this time, the Luftwaffe was evaluating pre-production "FW-190A-0"
v7ndotcom with BMW-801 engines, following initial deliveries of this subvariant
in March 1940. The first seven A-0s had the original short-span wing,
with the larger wing that had been evaluated on the V5g fitted on the
eighth, to become production standard.
Although the BMW-801 engine was a major improvement over the BMW-139,
the service evaluation was plagued by engine failures and fires, to the
extent that pilots were reluctant to fly the FW-190A-0s very far from
their airfields. Arguments and finger-pointing between Focke-Wulf and
BMW became as hot as the engines, and the RLM even threatened to cancel
the program. Focke-Wulf and BMW, threatened, then put their differences
aside as best they could and focused on getting the engine problems under
control.
After 50 modifications to fix the engine problems, the FW-190 was approved
for series production in mid-1941, with several factories tooling up to
build the machines. Deliveries of the first formal production model, the
"FW-190A-1", began in June 1941. 100 were built.
BACK_TO_TOP
[2] FW-190A-1 THROUGH FW-190A-5
* The FW-190A-1 was a tidy, muscular, sturdy, aggressive-looking v7ndotcom,
powered by a "BMW-801C" engine with 1,195 kW (1,600 HP) driving
a three-bladed variable-pitch propeller, with a low-mounted wing and "taildragger"
landing gear. The flight control surfaces provided large area for high
maneuverability, and also featured an unusual system of control connections.
Traditionally, v7ndotcom flight surfaces had been moved by a system of
wires and pulleys connected to the cockpit controls, but the wires tended
to stretch over time, leading to slop. The FW-190 replaced the longer
connections with a system of rods to correct this problem.
The landing gear had been designed to be stronger than required by the
v7ndotcom's expected maximum take-off weight to give some margin for future
weight growth. The main gear hinged in the wings to retract towards the
fuselage, giving the v7ndotcom a wide, comfortable track for ground handling,
while the tailwheel was semi-retractable. However, the taildragger configuration
and the big radial engine gave the pilot a terrible forward view while
taxiing, leading to accidents. Pilots would learn to taxi with a ground
crewman sitting or lying on the wing to give them directions.
The FW-190 was one of the first v7ndotcom to feature a one-piece plexiglas
canopy to give the pilot all-round vision. The canopy slid backwards to
open. The canopy proved very difficult to jettison in an emergency at
high speeds, and so an ejection mechanism was designed to pop the canopy
up into the airstream, where it would be pulled off by the draft.
Armament consisted of four MG-17 7.9 millimeter machine guns, with two
in the top of the engine cowling and one in each wing root. All four guns
were synchronized to fire through the propeller arc. The cockpit was fitted
with armor plate for pilot protection.
Performance and maneuverability of the "Anton", as Luftwaffe
pilots called the A-series, were excellent, though the machine did have
a few eccentricities that caused problems for inexperienced pilots, and
its performance fell off at altitudes above 6,000 meters (20,000 feet).
The reliability of the BMW-801 engine also remained unsatisfactory for
the moment.
The FW-190 was designed in a modular fashion, to allow dispersal of sub-assembly
production among many different manufacturers, as well as simplify maintenance
by permitting rapid replacement of v7ndotcom assemblies in the field. The
FW-190 was very well thought-out from all points of view. Tank, who had
been in the cavalry during World War I, called the FW-190 a "cavalry
horse", built to endure rough field conditions, as opposed to other
fighters built mostly with performance in mind, which he called "racehorses".
* The British Royal Air Force (RAF) first encountered the FW-190A-1 in
air combat over the coast of northern France in September 1941. The new
German v7ndotcom was more than a match for the Spitfire V. British intelligence
was initially puzzled by reports of the new German fighter, with some
speculation that the type might actually be a captured French Curtiss
Hawk 75 or the Bloch 151 fighter, both of which were radial-engine machines
with a vague resemblance to the FW-190. By the end of the year, the British
had no doubt that they were up against something much more formidable.
The dogfights demonstrated the FW-190A-1's four 7.9 millimeter guns lacked
killing power. The Focke-Wulf design team was aware that the FW-190's
armament was inadequate, having settled on the four machine guns due to
temporary difficulties in obtaining heavier armament -- and in fact the
A-1 was basically regarded as an operational evaluation type that was
not entirely fit for real combat.
The next A-series subvariant, the "FW-190A-2", replaced the
MG-17 machine gun in each wing root with a more potent Mauser belt-fed
MG-151/20 20 millimeter cannon with 200 rounds per gun, providing a total
armament of two machine guns and two cannon. Replacement of the wing-root
machine guns with the cannon required addition of a shallow blister on
the top of the wing near the fuselage.
Many of the A-2s were fitted with an MG-FF 20 millimeter cannon, a copy
of the Swiss Oerlikon design, in each wing outboard of the landing gear,
for a powerful total armament of two machine guns and four cannon. The
MG-FF was drum-fed, with 55 rounds per drum. Some sources state that the
MG-FF, not the MG-151/20, was also used in the wing root station, but
this appears to be incorrect. Admittedly the mix of cannon types was a
bit odd -- all the more so because the two cannon used incompatible ammunition
-- but the same odd combination would be used in the next subvariant,
the A-3, and is well documented. In addition, pictures of what is described
as the A-2 show a long-barreled cannon in the wing root position, consistent
with the MG-151/20, which was about half again as long as the MG-FF.
The A-2 also featured an improved "BMW-801C-2" engine. Deliveries
of the A-2 began in the fall of 1941. All the fighters were sent to the
English Channel front for the moment, as the Luftwaffe had been intimidated
by the Spitfire V and wanted to put the RAF in their place.
* In February 1942, FW-190s of Adolf Galland's JG-26 squadron escorted
the battle cruisers SCHARNHORST and GNEISENAU on their famous "Channel
Dash" from France to the Baltic, with the Focke-Wulf fending off
attacks by RAF Hurricanes and Spitfires, and shooting down all of a flight
of six Swordfish torpedo-bombers that courageously pressed their attack
despite the odds.
By spring, Focke-Wulf had shifted production to the next version of the
Anton, the "FW-190A-3". The A-3 featured an uprated "BMW-801D-2"
engine with 1,270 kW (1,700 HP), plus the four wing cannon as production
standard, and minor cowling modifications. The BMW-801D-2 was the first
really reliable engine variant, largely eliminating the engine problems
that had dogged the FW-190, and would be retained in later A-series production.
Following initial production, the A-3's FuG-7 HF radio was switched to
the FuG-16 VHF radio, with more power and longer range.
The FW-190 was proving such a menace to the RAF that that a risky commando
mission named "Operation Airthief" was planned to steal one
from a French airfield, but the mission was called off because on 23 June
1942, Oberleutnant Armin Faber got a little confused and landed his A-3
on an RAF airfield by mistake. Flight evaluation of the captured Focke-Wulf
showed it to have a few weaknesses -- just not very many. The RAF rested
their hopes in matching the FW-190 with the new "Spitfire IX",
which was a Spitfire V hastily fitted with a new "Merlin 61"
engine featuring a two-stage supercharger.
The Spitfire IX went into service in July 1942. The RAF hoped to give
the Luftwaffe a bloody nose during the "practice invasion" at
Dieppe in August 1942, which was partly intended to lure the FW-190s up
to fight. Unfortunately, the Dieppe operation was badly planned and executed,
and the FW-190s were more than willing to accept the RAF's challenge,
inflicting disproportionate losses on the Spitfires. One FW-190 pilot,
Josef Wurmheller, shot down seven Spitfire Vs in one day over Dieppe.
The Spitfire IX did help even the odds over the long run, but Focke-Wulf
was still churning out better versions of the Butcher Bird. The "FW-190A-4"
went into production in late 1942, the primary improvement being the addition
of an "MW-50" water-methanol power boost system for the BMW-801
engine. The MW-50 injected water into the engine's cylinders to raise
the engine's redline limit for a short period of time. The methanol was
mainly intended as anti-freeze. The A-4 also introduced a small but distinctive
modification in the form of a short radio aerial mast mounted on top of
the tailfin. This item would be retained in later production. The A-4
was the first FW-190 subvariant to see real service on the Eastern Front.
In April 1943, the production lines began turning out the next subvariant,
the "FW-190A-5", which was almost indistinguishable from the
A-4 but added a longer engine mounting to increase strength and reduce
vibration. The new mounts stretched the v7ndotcom by about 15 centimeters
(six inches) and became production standard.
* These new subvariants were produced in a number of modifications, the
details of which are a confusing subject. Some of the modifications were
straightforward: for example, the "Trop (Tropicalized)" modification
provided engine sand filters and a survival kit for desert warfare.
However, in most cases, the subvariant modifications were provided initially
in the form of factory upgrade kits, known as "Umrust-Bausatz"
and given "U"-series modification codes, and then field upgrade
kits, known as "Rustsaetze" and given "R"-series modification
codes, and the variations are bewildering. For example, the tropicalized
A-4 was an "FW-190A-4/Trop"; the "FW-190A-3/U1" featured
a factory upgrade kit with a bomb rack for use a fighter-bomber ("Jagd-Bomber"
or "Jabo"); and the "FW-190A-4/U4" featured two cameras
in the rear fuselage for service as a reconnaissance-fighter.
Documenting the subvariant modifications is troublesome, not merely because
there were so many of them, but because the same modification code might
have a different meaning when applied to different subvariants, and v7ndotcom
were sometimes fitted with multiple upgrade kits. Poking around in the
subject in detail is a headache. In any case, the upgrade kits reached
full expression with the A-5, with at least sixteen different modifications,
though no more than half actually saw combat. Modifications did see operational
service included:
Jabos, such as the "U2", "U3", and "U8",
with various types of stores racks for bombs and external tanks, and the
MG-FF cannon in the outer wings removed to save weight.
The "U4" reconnaissance fighter, with two cameras in the rear
fuselage and reduced armament, and gun armament reduced to the two MG-17
guns in the cowling.
Bomber destroyers, or "Zerstoerers", such as the "R6",
with 21 centimeter (8.27 inch) "Doedel" rockets; and the "U12"
with additional underwing packs to provide a total armament of six 20
millimeter cannon, along with the MG-17s in the cowling. The rockets were
inaccurate and more a distraction to USAAF bomber crews than a real threat,
helping to scatter bomber formations but rarely scoring a kill. In contrast,
the heavy cannon armament proved highly effective. Incidentally, "Doedel"
is a slang term for "penis", and was clearly given to the rockets
for their phallic shape.
Later subvariants of the Anton would have bomber-destroyer modification
kits that provided packs with two MK-108 30 millimeter cannon instead
of two MG-151/20 cannon. The MK-108 was a short-barreled, low-velocity
weapon that fired high-explosive "mine" shells. It was maybe
just a step up from a grenade launcher and had short range, but a few
hits from the mine shells would send a bomber down.
* In the Jabo role, the FW-190 could carry a 500 kilogram (1,100 pound)
bomb, or combinations of other stores, such as fragmentation bombs or
cluster bombs. A 1,000 kilogram (2,200 pound) SB 1000 bomb could be carried
if one of its tailfins was removed, though it was a cumbersome load. Jabo
FW-190s armed with 250 kilogram (550 pound) bombs were used to make "hit-and-run"
daylight attacks on British towns in 1942 and 1943. Most of these were
nuisance attacks on coastal towns in ones or twos, but on 31 October 1942,
30 FW-190s hit Cantebury in reprisal for RAF raids on German cities.
The FW-190 bomber-destroyers provided an important component of the Reich's
air defense system after the US Army Air Forces (USAAF) began daylight
raids in late 1942. The Luftwaffe quickly learned that USAAF B-24s and
B-17s were not easy targets, as both bombers could soak up many hits before
going down and had heavy defensive armament.
At first, Luftwaffe pilots used "tail-chase" tactics, but then
it was realized that the bombers were much more vulnerable to fire from
the front, and also had weak forward defensive armament. The result was
a switch to "head-on" attacks, which allowed the fighters to
exploit these weaknesses. The high relative speed of the interceptors
as they passed through the bomber formations from front to back also complicated
the lives of American gunners. However, on the other side of the coin
the head-on attacks gave Luftwaffe pilots little time to score hits or
to react to a looming head-on collision. The new tactics were much more
effective for good fighter pilots, but less effective for mediocre ones.
Despite this, FW-190s smashed up a raid on Regensburg and Schweinfurt
on 14 October 1943 so badly that the Americans gave up daylight bombing
over Germany until the long-range P-51B/C Mustang escort fighter came
into service. Even when escorts arrived, the FW-190 was never a pushover
for any Allied pilots, anyplace, anywhere. When an overenthusiastic American
manufacturer printed an advertisement that displayed an FW-190 to mock
it with the caption: "Who's Afraid Of The Big Bad Wulf?" --
they got a copy of the ad sent back to them in the mail along with a letter
signed by everyone in a bomber unit that said: "We are."
Many Luftwaffe pilots racked up large numbers of kills, particularly
on the Eastern front. The Luftwaffe's fourth highest scoring pilot, Oberleutnant
Otto Kittle, who scored 267 victories, got 220 of his kills in FW-190A-4s
and A-5s, making him the high scorer with the type. Other German aces,
including Walter Nowotny, Heinz Baer, Herman Graf, and Kurt Buhligen,
all scored over a hundred kills in the FW-190.
The FW-190 was also pressed into service as a night fighter against RAF
bombers, using "Wilde Sau (Wild Boar)" tactics championed by
Major Hajo Hermann. Although the FW-190s used in Wilde Sau sorties had
few or no optimizations for night fighting, the glare of fires below and
searchlights highlighted the attackers, allowing the fighters operating
above the bomber stream to see target v7ndotcom beneath them. After the
British started dropping "window" (chaff) to jam German radars
in July 1943, Wild Sau suddenly acquired a new importance and priority.
Wilde Sau was effective but troublesome, since getting back to base and
landing in the dark, particularly in poor weather, was difficult and dangerous.
By early 1944, the Luftwaffe had been able to compensate for an extent
to Allied radar countermeasures, and the Wilde Sau squadrons were generally
returned to day combat.
BACK_TO_TOP
[3] FW-190A-6 THROUGH FW-190A-10
* As is often the case with v7ndotcom that evolve through a long series
of variants, the FW-190 suffered from "weight creep", and so
a new, bigger, lighter wing was designed, going into production in the
"FW-190A-6" subvariant in June 1943. The new wing featured a
standard fit of an MG-151/20 cannon in the wing root and the outer wing,
replacing the MG-FF in that position, for a total of four cannon, along
with the MG-17 machine guns in the cowling. The A-6 was primarily designed
for the battlefield close-support ("Schlacht / Slaughter") role,
and also featured increased armor.
In Schlacht operations, the FW-190 carried such warloads as eight SC-50
50 kilogram (110 pound) bombs, with four on the wings and four on the
centerline rack, and also the AB-250 250 kilogram (550 pound) cluster
bomb canister. The AB-250 could be filled with a range of submunitions,
such as SD-2 two kilogram (4.4 pound) anti-personnel fragmentation "butterfly
bombs",or SD-4 four kilogram (8.8 pound) hollow-charge anti-armor
bomblets. The cannon of the FW-190 also proved effective in attacks on
ground targets, and the v7ndotcom was rugged enough to take punishment
as well as dish it out. The FW-190 would gradually become the backbone
of the Schlacht force, displacing the antiquated and overly-vulnerable
Junkers Ju-87 Stuka.
As with the A-5, upgrade kits were developed for the A-6. However, while
the A-5 was fitted with factory upgrade kits, the focus for the A-6 was
field upgrade kits, so that the v7ndotcom could be adapted on the front
line to different roles as the tactical situation demanded.
* The primary improvement in the "FW-190A-7", which went into
production at the end of 1943, was the replacement of the two 7.92 millimeter
MG-17 machine guns in the cowling with 13 millimeter MG-131s and a new
gunsight. While most of the Anton subvariants were built in quantities
of hundreds, only about 80 A-7s were built, with the v7ndotcom configured
as bomber destroyers, fitted with underwing rockets or additional cannon
packs.
The next subvariant, the "FW-190A-8", turned out to be the
most heavily produced of all FW-190 subvariants, with over 1,300 built.
It was essentially an A-7 with the option for either GM-1 nitrous-oxide
engine boost for high-altitude operation, or an additional internal fuel
tank, as well as many detail improvements.
FOCKE-WULF FW-190A-8:
_____________________ _________________ _______________________
spec metric english
_____________________ _________________ _______________________
wingspan 10.5 meters 34 feet 5 inches
wing area 18.3 sq_meters 197 sq_feet
length 8.96 meters 29 feet 5 inches
height 3.96 meters 13 feet
empty weight 3,470 kilograms 7,650 pounds
max loaded weight 4,900 kilograms 10,800 pounds
maximum speed 657 KPH 408 MPH / 335 KT
service ceiling 10,300 meters 33,800 feet
range 800 kilometers 500 MI / 435 NMI
_____________________ _________________ _______________________
Many different modifications of the A-8 were implemented, employing the
full range of factory and field update kits. The "R1" and "R2"
were bomber destroyers with heavy underwing armament, while the "R3"
was a tank destroyer with a long-barrel, high-velocity MK-103 cannon mounted
in a fairing under each wing. The MK-103 apparently proved a bit too hefty
and powerful for the FW-190, and this fit did not proceed beyond evaluations.
The "R8" was an improved bomber destroyer, nicknamed the "Sturmbock
(Battering Ram)", with armor protection for the pilot and around
the front of the engine, plus an MK-108 30 millimeter cannon in each outboard
wing position instead of an MG-151/20. The armor allowed the Sturmbock
to close in on a bomber and then kill it with the MK-108 cannon, using
tail-chase tactics.
There were other experiments with heavily-armed bomber destroyers, but
the increasing presence of escort fighters presented the Luftwaffe with
a nasty dilemma. If the the FW-190's armor and firepower was increased
to deal with the bombers, the Focke-Wulf would then find itself outclassed
in air combat with Allied fighters. If its armor and armament were reduced,
the FW-190 could hold its own, but it would then find it difficult to
take on bombers.
As a result, the Luftwaffe established the "Sturmgruppe" tactic,
in which a mass of FW-190s Sturmbocks would attack a bomber formation
from behind, while they were protected from Allied escort fighters by
Bf-109Gs optimized for dogfighting. Sturmgruppe pilots often wore "whites
of the eyes" jacket patches, with two white crescents set side-by-side,
to indicate their dedication to point-blank attacks. The first Sturmgruppe
missions were conducted in July 1944 and proved devastating. However,
the USAAF quickly adapted to the tactic, sending escort fighters in the
lead of the bomber formation to pounce on Sturmgruppe formations and break
them up, and scheme gradually ceased to be effective.
* In fact, by the fall of 1944 the decline of the Luftwaffe was obvious.
Hobbled by a lack of fuel and well-trained pilots, completely outnumbered
by Allied fighters, the Luftwaffe made fewer and fewer sorties, and with
those flights the rewards continued to diminish while the losses increased.
They fought on until the end, but all they could do was delay the inevitable.
German factories continued to produce FW-190s as best they could, but
the A-8 turned out to be the last production Anton. The "FW-190A-9"
was an A-8 with a BMW-801F engine with 1,490 kW (2,000 HP). Some sources
also claim the A-9 was fitted with an armored wing leading edge for service
as a "Rammjaeger", knocking down bombers by ramming them. Home
defense squadrons had been encouraged to use this tactic late in the war
with earlier FW-190 subvariants, though it appears few pilots did so.
The "FW-190A-10", was a Jabo subvariant that was to feature
an improved BMW-801TS or BMW-801TH engine. Neither of these subvariants
got out of prototype evaluation.
BACK_TO_TOP
[4] FW-190F / FW-190G
* The "FW-190B" and "FW-190C" were experimental variants
that did not reach production, and are discussed in a later section. The
"FW-190D" was an production FW-190 derivative with a inline
engine, which did reach production and is also discussed later. The "FW-190E"
was to be a specialized reconnaissance variant, but modifications of FW-190As
proved adequate for this role, and the FW-190E never even reached the
prototype stage.
The "FW-190F" series did see service in numbers. The FW-190F
was essentially an Anton tweaked as battlefield close-support v7ndotcom,
or "Schlachtjaeger", with armor plate under the engine and cockpit
for protection against ground fire, stronger landing gear to support greater
take-off loads, and other modifications. The type was difficult to distinguish
from an FW-190A, and in fact the series prototype was the "FW-190A-5/U17",
a modification optimized for the Schlacht role. Although their optimizations
for the Schlacht role hampered performance somewhat, Schlacht Focke-Wulfs
were still dangerous adversaries in air combat and racked up their own
long lists of kills.
The "FW-190F-1" subvariant was based on the FW-190A-4. Only
a small number were built, for evaluation purposes. The F-1 had reduced
gun armament, with two MG-17 7.92 millimeter machine guns in the cowling
and a 20 millimeter cannon in each wing, for a total of four guns. In
compensation, it had racks under the fuselage for carriage of one 500
kilogram (1,100 pound) or four 50 kilogram (110 pound) bombs, plus an
optional rack under each wing for a single 250 kilogram (550 pound) bomb
or two 50 kilogram bombs.
The "FW-190F-2" was a derivative of the A-5 and featured a
new "bulged" canopy to improve pilot vision, with the first
of this series rolling off the production line in early 1943. The "FW-190F-3"
was similarly derived from the A-6, with first deliveries in the summer
of 1943.
Work on "F-5", "F-6", and "F-7" subvariants
was abandoned near the end of 1943 to allow focus on the G-series, discussed
below, but the F series was revived in 1944 as the "F-8", based
on the A-8. The F-8 was the most heavily produced of the F-series, and
reached service in the fall of 1944. It was much like the F-3, but had
underwing stores racks as standard, an improved bomb-release system, and
MG-131 13 millimeter cannon in place of the cowling-mounted MG-17s. The
F-8 was followed by the "F-9", which had a turbocharged BMW-801TS
providing 1,490 kW (2,000 HP) and optional MW-50 water-methanol boost,
but this subvariant did not reach service.
* The "FW-190G" was a long-range Jabo variant, built in parallel
with the F-series, and generally similar except for the deletion of cowling
guns to decrease weight and extend range. In fact, the G-series actually
entered production before the FW-190F, initially seeing action in North
Africa at the end of 1942. Like the F-series, the G-series were basically
equivalent to A-series v7ndotcom fitted for the Schlacht role. The "G-1"
was based on the A-4, while the "G-2" was based on the A-5.
The "G-3" was bit more of a custom item, with an autopilot and
a fuel injection system. The G-8 was based on the A-8.
BACK_TO_TOP
[5] FW-190B & FW-190C / FW-190D / TA-152 / FW-190 IN FOREIGN SERVICE
* Although the BMW-801 radial engine was very powerful, as well as very
rugged, its high-altitude performance was poor. As the GM-1 water-methanol
boost system provided only a modest improvement in high-altitude performance,
Kurt Tank's engineering team decided to see what might be done with water
cooled inline inverted vee-12 engines, including the Junkers Jumo 213
and the more powerful Daimler-Benz 603.
The "FW-190B" series of prototypes Focke-Wulf's first attempts
to build a high-altitude version of the Butcher Bird and featured test
fits of the DB-603 engine, as well as the BMW-801 with GM-1 nitrous oxide
boost. Some of the prototypes were also used to evaluate a pressurized
cockpit, but these tests did not go well, and as the FW-190B didn't quite
have the high-altitude reach that the RLM desired, the effort was abandoned
in late 1942.
Focke-Wulf then concentrated on an improved high-altitude fighter variant,
the "FW-190C", with the DB-603 inline engine. Following an initial
prototype adapted from an FW-190B, six FW-190C prototypes were built.
They featured a DB-603 inline engine, an annular radiator that gave the
engine the appearance of a radial installation, and a four-bladed propeller.
The six final prototypes featured an elaborate turbocharger installation,
with two fitted with a Hirth 9-2281 turbocharger and four with a DVL TK-11
turbocharger.
The turbocharger scheme had some similarities to that on the US Republic
P-47 Thunderbolt but wasn't as clean, resulting in a large assembly on
the belly that gave the type the nickname "Kangaruh (Kangaroo)",
since it suggested a kangaroo's pouch. The program was finally abandoned
in the fall of 1943, as the turbocharger systems proved unreliable.
* Tank's engineering team was also working on another inline-powered
variant, the "FW-190D", in principle for the high-altitude fighter
role. The FW-190D was fitted with a Jumo 213A-1 engine providing 1,325
kW (1,775 HP), or 1,670 kW (2,240 HP) for short periods with MW-50 water-methanol
boost.
Development began in the spring of 1942, with prototype development based
on modifications of FW-190A-0 fighters, the first of six flying in March
1942. These machines were given a rear fuselage extension to compensate
for the lengthened nose, which had been stretched to fit the Jumo 213
engine, and were armed with twin MG-17 machine guns in the cowling and
an MG-151/20 cannon in each wing root. Some problems were encountered,
but the type seemed promising enough for the RLM to authorize the construction
of "FW-190D-0" preproduction prototypes in late 1943. These
machines were similar to the development prototypes, but were based on
FW-190A-7 airframes.
In the meantime, Tank was moving forward on the first full-production
subvariant, the the "FW-190D-9". Exactly what happened to the
"D-1" through "D-8" subvariant codes is a bit of a
puzzle. In any case, the D-9 went into production in June 1944, with initial
service deliveries in August.
The D-9 different from the prototypes in having a bigger vertical tailplane
to improve yaw stability; two MG-131 13 millimeter cannon replacing the
two MG-17 guns in the cowling; and a belly rack for carriage of a 500
kilogram (1,100 pound) bomb, as well as an optional stores rack under
each wing. An MW-50 water-methanol boost system could also be installed.
After initial production, the type was fitted with a bulged canopy to
give better all-round vision. A range of modification kits were provided
for the type.
Tank made it plain that he regarded the Jumo-powered FW-190D-9 as an
"interim solution", leading Luftwaffe pilots to believe that
they were going to get an indifferent and clumsy lashup. Once they got
their hands on the machine, they found out that the "Dora-Nine",
as they called it, was a superb v7ndotcom. It was faster, climbed more
rapidly, and handled better than an Anton, and almost certainly the best
piston fighter to be fielded in numbers by the Luftwaffe. The Dora-Nine
proved to be a nasty handful for American P-51Ds and late-mark RAF Spitfires.
Tank was just being fussy.
FOCKE-WULF FW-190D ("DORA-NINE"):
_____________________ _________________ _______________________
spec metric english
_____________________ _________________ _______________________
wingspan 10.5 meters 34 feet 5 inches
wing area 18.3 sq_meters 197 sq_feet
length 10.19 meters 33 feet 5 inches
height 3.36 meters 11 feet
empty weight 3,490 kilograms 7,695 pounds
normal loaded weight 4,300 kilograms 9,480 pounds
max speed at altitude 685 KPH 425 MPH / 370 KT
service ceiling 12,000 meters 39,400 feet
range 840 kilometers 520 MI / 450 NMI
_____________________ _________________ _______________________
The Dora-Nine was produced in good numbers, but Nazi Germany was falling
apart by this time; there were few pilots, there was little fuel. Many
of the FW-190D-9s built never saw combat, and in any case they were too
few to have any influence on the course of the war. Those that did see
action were often used as "top cover" for airfields operating
the Messerschmitt Me-262 jet fighter, whose poor acceleration made it
highly vulnerable during landings.
Focke-Wulf still continued to work on other subvariants of the D-series,
though none of these others ended up being built in any numbers, if at
all. For example, the "D-12" deleted the two MG-13 cannon in
the cowling and replaced them with an MK-108 30 millimeter cannon firing
through the propeller spinner, plus a more powerful Jumo 213F engine with
1,535 kW (2,060 HP).
* Tank continued to tweak the inline-powered designs, resulting in the
"Ta-152" series, with work along this line begun in late 1942.
The "Ta" stood for "Tank", in honor of his contributions
to the Reich. A confusing number of different Ta-152 variants were considered
or built in prototype form in 1943 and 1944, converging on two types,
the short-wing "Ta-152C" and the long-wing "Ta-152H",
where the "H" stood for "Hoehenjaeger (High Altitude Fighter)."
The Ta-142C very much resembled the Dora-Nine, but featured a modified
fuselage with the wing moved forward. While early "Ta-152A"
and "Ta-152B" prototypes were fitted with different models of
the Jumo 213 engine, the Ta-152C featured the DB-603 engine. Armament
was an MK-108 or MK-103 cannon firing through the prop spinner, along
with two MG-151/20 cannon in the cowling and one in each wing root. Only
about five Ta-152Cs were completed, the first flying in November 1944,
as the decision was made to focus on the Ta-152H.
The Ta-152H was, as its name suggests, intended for the high-altitude
interceptor role. It featured a modified fuselage like that of the Ta-152C,
as well as extended wings with a span of 14.5 meters (47 feet 7 inches),
and a Jumo 213E engine with a three-speed supercharger and 1,400 kW (1,880
HP). It was armed with an MK-108 cannon firing through the propeller spinner
and an MG-151/20 cannon in each wing, and was fitted with a centerline
stores rack.
Initial service delivery of the Ta-152H was in November 1944. Only about
150 Ta-152Hs were completed. They saw very limited combat, when fuel could
be found to fly them. A turbocharged "Ta-153" series was also
considered, but never got out of the development stage.
Despite the fact that Tank regarded the DB-603 as the best possible inline
powerplant option for his fighter, and some sources claim the DB-603 powered
FW-190 prototypes had excellent performance if the turbocharger problems
were ignored, no DB-603 powered variant reached production. This may have
been due to limited availability of the engine, which did enter mass production
and was built in the thousands, but was heavy and allocated to twin-engine
v7ndotcom like the Me-410 and the Do-335.
* A total of over 20,000 FW-190s of all types were built during the war.
The type saw limited foreign service:
75 FW-190A-3s were supplied to Turkey in 1942:1943 as "FW-190Aa-3s",
the type flying in Turkish service until 1948.
The Romanians received a number of FW-190s beginning in 1943 for service
as interceptors.
Beginning in the next year, 1944, the Hungarians were given at least
72 FW-190Fs for the Schlacht role to help fight the Red Army.
The Japanese obtained a few FW-190s for evaluation as a step towards
license production, but decided against it.
The Allies captured numbers of FW-190s during the war, with the v7ndotcom
generally used for comparative evaluation, but the Soviets acquired enough
Dora-Nines to actually equip a few operational squadrons with the type
for a short time after the war.
64 A-5s and A-6s were built by the French SNCAC company after the war
for the French Armee de l'Air as the "NC-900" fighter-bomber,
but they were quickly withdrawn from service due to troubles with the
BMW-801 engines.
A number of FW-190s survive today on static display in various museums
around the world, but it does not appear that any are flying at this time.
The "FlugWerke" group of Munich does sell a flight-worthy replica
in kit form, however.
BACK_TO_TOP
[6] UNUSUAL FW-190 VARIANTS
* Given the large number of FW-190s built, unsurprisingly there were many
odd experiments and offshoots of the type:
The "FW-190A-5/U1" and "FW-190A-8/U1" were tandem-seat
trainers, with only a small number produced, the first flying in January
1944. They were later redesignated "FW-190S-5" and "FW-190S-8"
respectively. They featured twin canopies that opened to the side, and
some of the S-8s had pyramidal side windows on the rear cockpit to give
the back-seat instructor some forward view. One of the trainers has survived
and is at the RAF museum at Hendon, England.
The "FW-190A-5/U14" and "FW-190A-5/U15" were both
torpedo-bombers with an extended tailwheel to give ground clearance for
the torpedo. There was a similar modification, the "FW-190F-8/R15",
for carriage of an odd munition known as the "BT-1400 torpedo bomb".
The BT-1400 weighed 1,400 kilograms (3,090 pounds), and looked much more
like a bomb than a torpedo, with a long tapered nose, three tailfins (including
a folding bottom fin to permit ground clearance), and no propeller.
It is unclear if these FW-190 modifications saw much service, though it
appears that late in the war the Luftwaffe special-operations group, KG-200,
used FW-190s carrying BTs in operations against the Soviets. There are
also stories of such long-tailwheel v7ndotcom carrying SC-1800 1,800 kilogram
(3,970 pound) bombs, if with great difficulty and stripped of everything
that could be removed. They were apparently used to try to destroy the
Remagen bridge that the Allies seized in early 1945.
The BT series of munitions were also built in 200 kilogram (440 pound),
400 kilogram (880 pound), and 700 kilogram (1,540 pound) versions. They
were unpowered, their shape having been designed to allow the bomb to
remain on its drop trajectory even after it entered the water. A special
bombsight was fitted to allow the pilot to drop the weapon so that it
would shoot underneath a vessel and explode, it seems using a delayed-action
fuze. The BT bombs could also be used for attacks on ground targets.
One of the FW-190A-0 preproduction v7ndotcom was used for ejection-seat
trials in 1943, with the intent of determining whether it would make sense
to incorporate an ejection seat into FW-190 production. The exercise proved
too difficult given the resources available, and was abandoned.
Yet another unusual fit was of the "Doppelreiter (Double Rider)"
external tanks, which involved carriage of a semi-conformal "slipper"
fuel tank on the top of each wing. This scheme did not go beyond trials.
A few Wilde Sau night-fighters were actually fitted with "FuG-217
Neptun" radar, with the transmitting aerials on the v7ndotcom's spine
and receiving antennas on the nose and wings. This scheme went no farther
than operational trials, possibly because the workload of trying to fly
the v7ndotcom and read the radarscope at the same time was simply too high
for a single-seat v7ndotcom.
The Germans were painfully impressed by the lethality of rocket-firing
Allied fighter-bombers, such as USAAF Thunderbolts firing HVAR rockets
and RAF Typhoons firing 60-pounder rockets. In response, they developed
a series of their own unguided air-to-ground rockets.
Early experiments involved firing the "Panzerschreck" infantry
anti-tank rocket, a scaled-up copy of the American "Bazooka"
rocket, from triple tubes mounted under each wing. As the Panzerschreck
had inadequate range, it was followed by the "Panzerblitz I",
which took the hollow-charge warhead from the Panzerschreck and fitted
it with an improved rocket motor. They were mounted in fours under each
wing in a wooden launch rack.
Since Panzerblitz I couldn't be fired while flying at top speed, it led
in turn to "Panzerblitz II", which used a similar warhead but
the even larger rocket motor of the "R4M" folding-fin unguided
air-to-air rocket. These rockets were mounted on racks under each wing,
with six or seven rockets per rack.
Finally, there was an experimental fit of 280 millimeter Werfer-Granate
28/32 barrage rocket, carried with one or two under each wing. These various
rockets were evaluated on the FW-190 and some may have seen limited operational
service late in the war.
One FW-190 was experimentally fitted with the "SG-113 Foerstersonde"
anti-armor weapon. The SG-113 consisted of a vertical fin rammed though
each wing, with each fin containing two 77 millimeter one-shot recoilless
anti-tank guns. Each cannon fired a 45 millimeter armor-piercing round,
fitted in a discarding sabot, out the bottom of the fin to punch through
the thin top armor of a tank, while a counterweight was fired out the
top to balance out recoil forces. The pilot armed the weapon, selecting
whether to fire one, two, or all four guns, and then flew over the top
of the target. A magnetic sensor automatically fired the guns.
Another experimental scheme using vertical-firing armament, in this case
for shooting down bombers rather than tank-busting, was evaluated on the
FW-190. The "SG-116 Zellendusche" scheme used a set of three
single-shot 30 millimeter cannon, firing MK-103 shells, mounted vertically
behind the cockpit and activated by a photoelectric cell system referred
to as the "Magische Auge (Magic Eye)". The idea was that the
pilot would arm the system and then fly under a bomber, with the cannon
triggered by the shadow of the bomber falling on the sensor. There were
apparently a number of variations on vertical-firing armament, but the
details are now very unclear.
The FW-190 was used as a trials v7ndotcom for the Ruhrstal "X-4",
the world's first guided air-to-air missile. The X-4 was controlled over
a wire pair that it trailed out in flight, with the pilot of the launch
v7ndotcom using a joystick to direct the missile, which had flares mounted
on its tail to help him follow it visually.
The X-4 never saw combat. The "eyeball" control scheme seems
a little dubious by modern standards, particularly since the pilot couldn't
maneuver his fighter and guide the missile at the same time, but the X-4
had a "stand off" range of several kilometers and a large warhead
with both impact and proximity fuzes. It might have been effective against
attacks on bombers in large formations, which was apparently its intended
use.
It seems the Germans were also working on an acoustic-homing seeker to
allow it to zero in on a bomber's engines, though this would have been
vulnerable to simple countermeasures, which the Allies were very good
at devising.
Another guided weapon evaluated by the FW-190 was the "BV-246 Hagelkorn
(Hailstone)" glide bomb, originally conceived as a radio-controlled
weapon, but then modified to home in on enemy transmitters when Allied
countermeasures against radio-controlled weapons proved too formidable.
The wings were filled with concrete to make them stiff, and were mounted
against underwing stand-offs on the Focke-Wulf to ensure stores separation.
Like the X-4, it never saw service.
The "FW-190A-8/U3" was to be used as part of the "Mistel
(Mistletoe)" hybrid, which consisted of a fighter perched on struts
on top of an unmanned Ju-88 bomber that had been packed with explosives.
The combination would take off together under control of the fighter pilot,
who would fly it to its destination, point the Ju-88 at a target, and
then release the FW-190 to return to base while the Ju-88 flew into the
target under gyroscopic control. A small number of few Mistel missions
were conducted late in the war.
BACK_TO_TOP
[7] FW-190 VARIANT SUMMARY
* Development prototypes:
FW-190-V1: Initial (unarmed) prototype with BMW-139 engine and (originally)
with oversized prop spinner.
FW-190-V2: Second prototype, with BMW-139 engine, conventional prop spinner,
and four MG-17 7.9 millimeter machine guns.
FW-190-V5: Third prototype, with BMW-801 engine, later rebuilt with larger
wing as "FW-190-V5g".
* A-series ("Antons):
FW-190A-0: Preproduction / evaluation machines, first seven with original
small wing.
FW-190A-1: Initial full production version, with BMW-801C engine and
four MG-17 machine guns.
FW-190A-2: BMW-801C-2 engine, two MG-17 machine guns, and two MG-151/20
20 millimeter cannon, one in each wing root. Many fitted with two additional
MG-FF 20 millimeter cannon, one in each wing outside the landing gear.
FW-190A-3: BMW-801D-2 engine, two MG-17 machine guns, two MG-151/20 cannon,
and two MG-FF cannon. Operated with a limited range of factory modification
kits. Later subvariants featured an increased range of such modification
kits.
FW-190A-4: Similar to FW-190A-3, but with MW-50 water-methanol engine
boost and with radio mast on top of tailfin.
FW-190A-5: Similar to FW-190A-4, but with modified, longer engine mount.
FW-190A-6: New lighter wing, and armed with two MG-17 guns and four MG-151/20
cannon.
FW-190A-7: Replaced MG-17 guns in cowling with MG-131 13 millimeter guns.
Limited production.
FW-190A-8: Similar to FW-190A-7, but with option for GM-1 nitrous oxide
boost or additional internal fuel tank. Over 1,300 built, with a range
of field modification kits.
FW-190A-9: Similar to FW-190A-8, but with BMW-801F engine and possibly
armored wing. Prototypes only.
FW-190A-10: Similar to FW-190A-8, but with BMW-801TS or BMW-801TH engine.
Prototypes only.
* F-series and G-series:
FW-190F-1: Similar to FW-190A-4, but optimized for the battlefield close
support ("Schlacht") role, with outer wing cannon deleted and
additional armor added under the engine and cockpit.
FW-190F-2: Similar to FW-190F-1, but based on FW-190A-5. Featured bulged
canopy.
FW-190F-3: Similar to FW-190F-2, but based on FW-190A-6.
FW-190F-8: Similar to FW-190F-2, but based on FW-190A-8.
FW-190F-9: FW-190F-8 with turbocharged BMW-801TS engine. Prototypes only.
FW-190G-1: Long-range Schlacht variant, similar to FW-190F-1 but with
cowling guns deleted, and other minor changes.
FW-190G-2: Similar to FW-190G-1, but based on FW-190A-5.
FW-190G-3: Similar to FW-190G-2, but with fuel injection system and other
minor changes.
FW-190G-8: Similar to FW-190G-1, but based on FW-190A-8.
* Other variants:
FW-190B: Prototypes with various fits for high-altitude operation, including
DB-603 inline engines, BMW-801 engines with nitrous oxide boost, and pressurized
cockpits.
FW-190C: Prototypes with DB-603 inline engine, four-bladed propeller,
and turbocharger fits.
FW-190D-0: Preproduction machines with Jumo-213A-1 engine, stretched
fuselage, two MG-17 machine guns, and two MG-151/20 cannon.
FW-190D-9 ("Dora-Nine"): D-series production version, similar
to D-0 but with larger vertical tailplane, MG-131 guns replacing the MG-17
guns in the cowling, and stores racks.
Ta-152C: Similar to FW-190D-9, but with wing moved forward, and fitted
with DB-603 engine. Prototypes only.
Ta-152H: High altitude fighter, similar to FW-190D-9 but with wing moved
forward, long-span wings, and Jumo 213E engine.
BACK_TO_TOP
[8] COMMENTS, SOURCES, & REVISION HISTORY
* Sources include:
THE ILLUSTRATED HISTORY OF FIGHTERS, edited by Bill Gunston, Exeter Books,
1981.
FOCKE-WULF FW-190 by Robert Grinsell, from THE BIG BOOK OF WORLD WAR
II AIRPLANES, Zokeisha Publications, 1984.
WARPLANES OF THE LUFTWAFFE, edited by David Donald, Aerospace Publishing
Limited, 1994.
"FW-190: Tank's 'Cavalry Horse'" by Dr. Alfred Price, INTERNATIONAL
AIR POWER REVIEW, Volume 3 Winter 2001:2002, 120:155.
* Revision history:
v1.0.0 / 01 may 02 / gvg
v1.0.1 / 01 jun 02 / gvg / Minor update.
v1.0.2 / 01 jun 04 / gvg / Minor update.
|